[Features]
◆ Using 32 bit ARM chip set, operate on LINUX OS, speed up to 200MHz
◆ Direct connection to PC via TCP/IP port. Need not require TCP/IP converter. Transmission speed up to 100Mbps
◆ Controlling a 128-story elevator
◆ Able to link with intercom systems and manage up to 142 households
◆ Max. 100,000 Card Holder; Max 100,000 lines transaction
◆ Using Flash Memory to store data. Data can be stored up till 10 years
◆ Recoverable 100,000 lines of transaction should there be any system failure
◆ Update firmware via TCP/IP or RS-232 connector
◆ Equipped with input supervisory circuits. Able to send fault alert should there be any line tamper or
interruption
◆ Integrated with PLC function
◆ CE Certified
[Functions]
| Function |
Description |
| Connect External Reader |
Connect RS-485 reader, RS-485 card reader module, or RS-485 keypad reader to SKDC |
| Connect External SKDC |
Connect Card Reader via SKDC to SK800L controller |
| Connect External SK8I/O |
Can connect to 16 units of SK8I/O, each SK8I/O comes with 8 DI and 8 DO, which can manage up to 128 floors elevator and is able to connect to 142 households intercom system |
| Communicate with PC |
1.
RS-232/485 or TCP/IP. Use dial-up switch to set RS-232
or RS-485
2. Use keypad to setup Controller ID
3. Use Keypad to setup IP Address, Subnet Mask and Gateway
|
| Offline add and delete card |
Yes |
| Dual cards Verification |
Yes |
| Same Card Delay
Control |
0~255 seconds. Factory default is
0 |
| Time Zone Control
|
32 groups of time zone |
| Holiday Control |
Yes |
| Report Loss
Card |
Yes |
| Card Validity
Control |
Yes |
| Door Auto Release
Time Zone |
Yes |
| Card No. Output Byte |
1~4. Default is 3
|
| Card Display Format
|
HEX,DEC,ABA,USER
CODE. Default is ABA
|
| Communication
Monitoring
|
Yes |
| Tamper Alarm |
Yes |
| Terminal Resistance
|
Via Dial-up switch to determine whether
or not to terminate resistance
|
| RS-485 Reader ID Setup
|
RS-485 Reader has to connect to SKDC and changes ID address via controller |
| Power Monitoring
|
Main power supply failure alarm and
backup battery low voltage alarm
|
| Connect External
Battery |
Yes |
[Technical Specification]
| Parameter |
Description |
| CPU |
ARM9, processor speed up till 203MHz |
| Operating System |
Linux |
| Card Capacity
|
100,000 |
| Card Matching
Speed |
< 1 seconds when controller card
storage reaching 100,000 cards |
| Storage Capacity |
100,000 lines, on 64M SDRAM and 16M NOR FLASH |
| No. of Floors Control |
128 |
| Intercom Linkage |
Can connect to 142 households intercom system |
| COM
Port
|
3 ports，Com0 & Com1 can be switched to RS-232 or RS-485 using dial-up switch
(1) Com1 – PC or child controller
(2) Com2 – SKDC, SK8I/O, universal reader
(3) Com0 – Factory debugging |
| TCP/IP |
1, communicate with PC at 10M/100M
|
| USB |
2个Master USB |
| IIC |
1 |
| SD卡 |
1 |
| JTAG |
1 |
| Operation Keypad |
128x64 dots LCD, 4x4 keypad |
| TTL Input |
16, for PLC use |
| Analog Input |
7 |
| Relay Output |
8, 12V/10A, can control floor's button |
| TTL
Output |
8, 5V/300mA, controllign floor's button, can change to become relay signal using TTL converter |
| Reset Switch |
Yes |
| Tamper Switch |
Yes |
| Buzzer |
Yes |
| Clock Power
Battery
|
CR2032,3V |
| Supply Voltage
|
9-30V/400mA |
| Operation Temperature
|
-10~50 ℃ |
| Dimension |
240 X 180 X 30mm |
| Housing |
ABS flame-resistant, silvery gray color |
[Application Area]
◆
Lift Control and Management
[Downloads]
Current Page in MS Word Document
Product Manual
Installation Dimension
Typical Connection
Product Brochure
[Related Links]
Elevator
Card Management System
SK400L Lift Controller
SK8I/O Elevator Extension Module
SKDC Door Controller
TTL Converter
Product Certification
Standare Elevator Management System
Standard Telephone Access Elevator Management System
|
