|
|
|
|
SK100V-NT Series
Video Access Controller
|
|
 |
[Features]
◆ Capture image after swapping card to prevent card being used by unauthorized
◆ Build-in web server, online surveillance via IE browser
◆ Using 32 bit ARM chip set, operate on Linux OS, speed up to 200MHz
◆ Direct connection to PC via TCP/IP port. Transmission speed up to 100Mbps
◆ Maximum 10,000 card holders and 100,000 lines transaction
◆ Transaction data can be exported via USB thumb drive
◆ Upload image to PC via FTP
◆ Using Flash Memory to store data. Data can be store
up till 10 years
◆ Recoverable 100,000 lines of transaction should there
be any system failure
◆ Update firmware via TCP/IP or RS-232 connector
◆ Smart Door Lock capability
◆ Separately configure door access mode by PIN or Time Zone Control
◆ Display name and ID when access is granted
◆ CE Certified
|
[Functions]
| Functions |
Description |
| Camera |
1/4＂COMS
Sensor，Resolution: 640x480dpi，Focus length: 3.6mm,
Angles: 60°，RGB 24bit True Color, Intelligent
AE Exposure，Image format: JPEG, Power: 60mA |
| Image Capacity |
Controller keeps up to 800 images, expandable to 100,000 with 1GB SD card. Image size at 8K; upload to computer via FTP. |
| Monitoring |
Built-in
Web Server, viewing can be via IE Browser |
| Card Open Door |
Connect to wiegand reader |
| Card + PIN Open Door |
1. Using Access Controller
2. Connect external SK10K or SK100K-CN (Chinese
version keypad reader)
via wiegand connector. Set it to free wiegand.
3. Select either PIN only or Card ID only to open door.
4. Card + PIN open door: 4 digits PIN; PIN only open door: 8 digits PIN |
| PIN Open Door |
| Card ID Open Door |
| Fingerprint Open Door |
Connect SK fingerprint card reader via wiegand. At the same time the following mode can be implemented: Card + Fingerprint, ID + Fingerprint, Fingerprint + PIN, Card + Fingerprint + PIN, ID + Fingerprint + PIN, Card Only, Card + PIN, PIN Only , Card ID Only etc. |
| Connect External 26/32 Wiegand Card Reader |
Yes |
| Free Wiegand Setup |
Yes. Can set low battery voltage alarm when use with long range card reader. |
| Connect External Keypad Reader |
1. HID wiegand keypad reader
2. SK Chinese keypad reader, via wiegand connector |
| Connect External SK Fingerprint Reader |
via wiegand connector |
| Connect to Computer |
1. RS-232/485 or TCP/IP. Use jumper setting to determine RS-232 or RS-485
2. Use keypad to set controller's ID
3. Use keypad to set controller's IP address, subnet mask and gateway |
| Door Force Open Alarm |
Yes |
| Door Open Too Long Alarm |
1~255 seconds. Factory default is 5 seconds. Alarm output can be disabled. |
| Offline Insert & Delete Card |
Yes |
| Dual Card Verification |
Yes |
| Invalid PIN Control |
When using Card + PIN open door and number of PIN retry is over preset limits, the door will be remain locked until locking period is over then it is able to use. |
| Same Card Delay |
0~255 seconds. Factory default is 0 |
| Time Zone Control |
32 groups of time zone |
| Holiday Control |
Yes |
| Report Loss Card |
Yes |
| Card Validity Control |
Yes |
| Door Auto Release Time Zone |
Yes |
| Anti-passback |
Yes |
| Card No. Output Bytes |
1~4. Default is 3 |
| Card Display Format |
HEX,DEC,ABA. Default is ABA |
| Communication Monitoring |
Yes |
| PIN and Time zone Control |
Can be setup to use either PIN control or time zone control |
| Tamper Alarm |
Yes |
| Reset Door Open Too Long Record |
Yes |
| Terminal Resistance |
Setting via jumper |
| Sensor Setup |
Door sensor normal behavior; sensitivity control; whether transaction based on door sensor action. |
| User Name Display |
Display Name and ID after access is granted |
[Technical Specification]
| Parameters |
Description |
| CPU |
ARM9 chip, speed reaching 200MHz |
| Operating System |
Linux |
| Control Door Area |
1 |
| Connect wiegand reader |
2 |
| Magnetic Sensor Signal |
1 |
| Push Button Signal |
1 |
| TTL Alarm Input |
1 |
| Door Open Relay |
1, 12V/1A |
| Alarm Relay |
1, 12V/1A |
| TTL Alarm Output |
1, 5V/300mA |
| Tamper Switch |
1 |
| Card Capacity |
10,000 |
| Card Matching Speed |
<0.5 seconds when controller card storage reaching 10,000 cards |
| Transaction Capacity |
100,000 lines |
| COM Port |
2 ports. 1 for RS-485 to communicate with PC and the other one via RS-232 to communicate with printer or other devices |
| TCP/IP |
1, communicate with PC at 10M/100M |
| SD Card |
Support |
| USB |
2 Master USB |
| Operation keypad |
128x64 dots LCD, 4x4 keypad |
| Buzzer |
Yes |
| Clock Power Battery |
CR2032, 3V |
| Supply Voltage |
9-30V/400mA |
| Operation Temperature |
-10~50 °C |
| Dimension |
158×112×37mm |
| Housing |
ABS flame-resistant, silvery gray color |
[Choosing A Model]
| Model
No. |
Description |
| SK100V-NT |
Single Door Video Controller |
| SK100VE-NT |
Video Access Controller c/w EM Card reader. Reading distance:>10cm |
| SK100VM-NT |
Video Access Controller c/w Mifare Card reader. Reading distance:>2.5cm |
| SK100VH-NT |
Video Access Controller c/w HID 125KHz Card reader. Reading distance:>4cm |
|
|
[Application Area]
◆ Door Access Control and Management
◆ Car Parking Control and Management
◆ Attendance Management
◆ Channel Management
◆ Environmental Monitoring and Management
[Relevant Information]
Product Manuals
Installation Meassurement
Typical Connection Diagram
Product Brochures
Camera Technical Specification
[Related Links]
SK200-NT 2 Doors Controller
SK400-NT 4 Doors Controller
SK800 8 Doors Controller
Product Certification
[Customization API]
◆ Offer SDK Dynamic Library
◆ Offer Delphi, VB, VC, PB Demo Program
◆ Support Serial COM and TCP/IP communication
|
|
|
|
