Feature:
◆
Built on 32 bits ARM technology running Linux operation
system
◆
Support LAN (10/100Base T - TCP/IP) or Serial (RS485 or
RS232) communication to PC Host.
◆
Support maximum of 8 doors with In and Out Wiegand/RS485
Reader through SKDC Door Controller
◆
Support 100,000 Cards and 100,000 Records. Under the condition
of 100,000 cards stored in the controller, the card search
response time will not be compromised which is still lesser
than one second for the last card found.
◆
Support maximum of 5 serial communication levels
◆
Data store in 16MB NOR Flash that will not be lost even
if powering off.
◆
Last 100,000 records can be resent to PC when the backend
system database is damaged.
◆
Online update firmware by TCP/IP
◆
Monitor TTL inputs. To handle very secure requirement, all
TTL input points can be configured to monitor four input
states: Alarm, Normal, Fault-Short and Fault-Open.
◆
With PLC logic built-in, all advances configuration can
be setup through PLC logic using XPLOC Designer. Engineer
or Advance User is able to make any logic change or adjustment
in the field without the need to change the program source
code.
◆
It has 16 TTL DI, 8 relay output and 8 TTL DO on board to
monitor alarm or status and control other equipment. If
necessary, up to 16 SKIO boards can be connected to SK800
to monitor status of up to 144 TTL inputs and control more
devices
◆
Support Global and Nested APB control
◆
Support Super Master Card during Emergency or System Failure
situation (SKDC comm. Fail or SK800 fault). This card will
be stored in SKDC non-volatile memory (EEPROM) and will
generate special record when presented.
◆
Intelligence door lock control (door lock back immediately
if system detect a door open and close condition irregardless
of door release time setting).
◆
Support Door sensor sensitivity adjustment (0-5 second)
◆
Enable/Disable Door only open by first card even Door is
suppose to free by Timezone
◆
Enable/Disable Exit control by Timezone
◆
Enable/Disable Exit require PIN
SK800
Door Controller Specification
| Item |
Specification |
Remarks |
| CPU |
ARM 9201 Core |
Frequency up to 203MHZ |
| Operating System |
Linux |
|
| Record |
100,000 |
|
| Card Holder |
100,000 |
|
| Number of Door |
8 |
In and Out Reader(RS485 or Wiegand) |
| Card Response Time |
<1 second |
Even 100,000 cards store in the controller |
| Menory |
64M SDRAM and 16M NOR FLASH |
|
| RS232 |
1 |
Reserved for Factory Testing |
| Serial Port |
3 |
COM1 for PC,COM2 for SKDC/SK10/SK Controller,COM3
reserved.COM1 and COM2 can both be configured to RS485
or 232 |
| TCP/IP |
1 |
10M/100M |
| USB |
2 |
Master USB and Slave USB |
| 11C Bus |
1 |
|
| SD Host Interface |
1 |
|
| JTAG |
1 |
|
| TTL Input |
16 |
Monitoring sensor |
| A/D Convertor |
7 |
Analogue Signal Input |
| SPI Bus |
1 |
|
| Relay Output |
8 |
12V/10A |
| TTL Output |
8 |
5-24V,Max 200mA |
| Wiegand Port |
2 |
Format 26/34 compatible (Reserved) |
| IP Setting |
By Keypad |
|
| Device ID |
By Keypad |
1-255 |
| Reset Switch |
Yes |
Terminal Block available for External Reset Switch
|
| Tamper |
Yes |
|
| Buzzer |
Yes |
|
| Watchdog |
Yes |
|
| Battery Backup |
Yes |
The controller charges up battery automatically and
switches to battery when main power fails |
| External Battery Low Sigual |
Yes |
When hattery is at lower 9.5v |
| Main Power Fail Sigual |
Yes |
|
| Keypad |
4×4 |
Blue Backlight |
| Display |
128×64 dots |
Graphical with White Backlight |
| Battery for RTC |
CR1220.3V |
Last for 6 months if not powering up |
| Power |
220V/400mA |
|
| Work Temperature |
-10～50℃ |
|
| Storage Temperature |
0～50℃ |
|
| Dimension |
320*245*65 mm |
Main Board;195mm×170mm×50mm |
| Weight |
4kg |
Including Metal Case but not battery |
|
|
